Campbell-scientific AP200 CO2/H2O Atmospheric Profile System Manual de usuario Pagina 54
- Pagina / 120
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AP200 CO
2
/H
2
O Atmospheric Profile System
If seq_ACTIVE is True, then set STOPsequence = True to stop the sequence
and then verify that seq_ACTIVE changes to False.
Set valve_number to Zero (9). Look at the LEDs on the valve module to
confirm the selected valve is now active.
The CO2_SPAN_PPM variable displays the concentration in the CO
2
span
tank.
Check the value of diag_AP200. If it is not zero, a problem in the AP200
system should be resolved before continuing (see Appendix B, AP200
Diagnostics).
Wait for the values of CO
2
and H
2
O to stabilize. Normally, this takes one or
two minutes.
Record the value of CO
2
. This is the measured CO
2
concentration in ppm. If
the zero cylinder is selected, the value should be close to zero. If the CO
2
span
tank is selected, it should be close to the value of CO2_SPAN_PPM.
Record the value of H
2
O. This is the measured H
2
O concentration in ppt. The
value should be close to zero for either cylinder.
Set valve_number to CO
2
span (10) and repeat the previous steps.
Press <Esc> to return to the Manual Zero/Span menu.
6.2.2 Do CO
2
and H
2
O Zero
At the Manual Zero/Span menu, select <Do Zero (CO2&H2O)>. This menu
guides the user through the steps to flow the zero gas and to send the command
to zero the IRGA.
If seq_ACTIVE is True, then set STOPsequence = True to stop the
sequence. Then verify seq_ACTIVE changes to False.
Set valve_number to Zero (9). Look at the LEDs on the valve module to
confirm the Zero valve is now active.
Check the value of diag_AP200. If it is not zero, a problem in the AP200
system should be resolved before continuing (see Appendix B, AP200
Diagnostics).
42
- INSTRUCTION MANUAL 1
- Limited Warranty 3
- Assistance 4
- Precautions 5
- Figures 9
- Table of Contents 12
- AP200 CO 13
- O Atmospheric Profile 13
- 3. Initial Inspection 14
- 4. Overview 14
- 4.1.2 Optional Components 16
- 4.1.3 Common Accessories 18
- 4.1.4 Other Accessories 21
- 4.1.5 Support Software 21
- 4.1.6 Replacement Parts 22
- 4.2 Theory of Operation 23
- 4.2.1 Intake Assemblies 25
- Ambient Pressure (kPa) 26
- 4.2.2 Valve Manifold 27
- 4.2.3 Pump Module 28
- 4.3 Specifications 30
- 5. Installation 32
- 5.1.2 AP200 Enclosure 33
- 5.1.3 Intake Assemblies 33
- 5.2 Plumbing 35
- 5.2.2 Zero and CO 37
- 5.2.3 H 38
- 5.3 Wiring 39
- 5.3.2 Intake Heater Cables 40
- 5.3.3 Power 44
- 5.4 Configure the Program 46
- 5.4.2 Compile Switches 49
- 5.6 Verify Performance 50
- 5.6.3 On-site System Checks 51
- 6.1 Automatic Zero and Span 52
- 6.2 Manual Zero and Span 53
- 6.2.2 Do CO 54
- 6.2.3 Do CO 55
- 6.2.4 Do H 56
- 7.1 Plumbing Leaks 58
- 7.2 Enclosure Desiccant 59
- 7.3 Intake Filters 59
- 7.4 LI-840A (IRGA) 62
- 7.4.2 Configuring the IRGA 63
- 7.5 Zero/Span Flow 64
- 8. Repair 65
- CONFIG CO2_SPAN_PPM ppm CO 79
- Appendix D. Output Tables 81
- Appendix H. Using Swagelok 105
- Fittings 105
- Back ferrule 107
- Front ferrule 107
- Pf 101046.30007.1 111
- J.1 Introduction 113
- J.2 Removal 113
- J.3 Installation 116
Relacionado con productos y manuales para Instrumentos de medición Campbell-scientific AP200 CO2/H2O Atmospheric Profile System
Instrumentos de medición Campbell-scientific Bowen Ratio Instrumentation Manual de usuario
(36 paginas)
(36 paginas)
Instrumentos de medición Campbell-scientific CHP1 Pyrheliometer (from Kipp & Zonen) Manual de usuario
(23 paginas)
(23 paginas)
Instrumentos de medición Campbell-scientific CDM-VW300 Series Dynamic Vibrating-Wire Analyzer S Manual de usuario
(122 paginas)
(122 paginas)
Instrumentos de medición Campbell-scientific CM3 Kipp and Zonen Pyranometer Manual de usuario
(16 paginas)
(16 paginas)
Instrumentos de medición Campbell-scientific CMP6-L, CMP11-L, and CMP21-L Pyranometers Manual de usuario
(42 paginas)
(42 paginas)
Instrumentos de medición Campbell-scientific CM6/CM10 Tripod Weather Station Installation Manual de usuario
(68 paginas)
(68 paginas)
Instrumentos de medición Campbell-scientific CPEC200's EC155 Gas Analyzer's Packing I Manual de usuario
(1 paginas)
(1 paginas)
Instrumentos de medición Campbell-scientific CR10TCR Thermocouple Reference Manual de usuario
(10 paginas)
(10 paginas)
Instrumentos de medición Campbell-scientific CPEC200 Quickstart Guide Manual de usuario
(16 paginas)
(16 paginas)
Instrumentos de medición Campbell-scientific CR10XTCR Thermocouple Reference Manual de usuario
(12 paginas)
(12 paginas)
Instrumentos de medición Campbell-scientific CPEC200 Closed-Path Eddy-Covariance System Manual de usuario
(112 paginas)
(112 paginas)
Instrumentos de medición Campbell-scientific CR200/CR200X-series Dataloggers Manual de usuario
(208 paginas)
(208 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.102 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales