Campbell-scientific AP200 CO2/H2O Atmospheric Profile System Manual de usuario descargar pdf (Pagina 10)

Table of Contents

5-14. Tabs for opening intake assembly ..................................................... 30

5-15. Wiring of heater cable on AP200 intake assembly ............................ 30

5-16. Three intake assemblies with heater cables daisy chained to the

AP200 system enclosure ................................................................ 31

5-17. Proper wiring of power cable onto DIN bus of AP200 system

enclosure ........................................................................................ 33

5-18. Power cables secured to cable tie loop on pump module of AP200

enclosure ........................................................................................ 33

5-19. Cut-away view showing proper replacement of feedthrough cap ...... 34

7-1. Releasing rain diverter from intake assembly ................................... 48

7-2. Order of replacement for orifice, filter, and rain diverter .................. 49

7-3. Correct reassembly after filter replacement ....................................... 49

7-4. Installed IRGA in system enclosure .................................................. 50

7-5. Components and fittings of IRGA installation .................................. 51

E-1. 107-L temperature probe mounted with radiation shield .................. E-1

G-1. Installation location of power adapter ............................................. G-1

G-2. Bundled cable of power adapter ...................................................... G-1

G-3. Cable extension connected to AP200 power input terminal ............ G-2

G-4. AC power cord secured within AP200 system enclosure ................ G-3

G-5. Power adapter output cable plugged into cable extension ............... G-3

H-1. Swagelok

insert ............................................................................. H-3

H-2. Front and back Swagelok

ferrules ................................................. H-3

H-3. Swagelok

plug ............................................................................... H-4

H-4. Swagelok

cap ................................................................................. H-4

J-1. Location of pump enclosure inside AP200 system enclosure ...........J-1

J-2. Location of six screws of pump enclosure cover ...............................J-2

J-3. AP200 pump ......................................................................................J-2

J-4. Location of pump connector in AP200 pump electronics .................J-3

J-5. Self-tapping screws attaching pump to metal box .............................J-3

J-6. Location of cuts to remove pump assembly from tubing ..................J-4

J-7. Inlet and outlet tubing reconnected to pump .....................................J-4

J-8. Pump side with inlet and outlet tubing connected .............................J-5

Tables

5-1. Equivalent Resistance for Intake Heaters Connected in Parallel ....... 32

7-1. IRGA Settings ................................................................................... 52

7-2. IRGA Outputs .................................................................................... 52

B-1. Summary of Bit Numbers Indicating Conditions Outside Normal

Operating Range .......................................................................... B-1

C-1. Public Variables .............................................................................. C-1

D-1. Variables of the IntAvg Table ......................................................... D-1

D-2. Variables of the CalAvg Table ........................................................ D-4

D-3. Variables of the SiteAvg Table ....................................................... D-6

D-4. Variables of the RawDataTable ....................................................... D-8

D-5. Variables of the TimeInfo Table ................................................... D-10

D-6. Variables of the message_log Table .............................................. D-12

F-1. Profile Sequence-timing Variables ................................................... F-1

F-2. System Configuration Variables of Zero/Span ................................. F-3

F-3. Timing for Zero/Span Sequence (check only) .................................. F-4

F-4. Timing for Zero/Span Sequence (setting the IRGA) ........................ F-5

H-1. Available Plastic Tubing Sizes, Construction, and Usage

Guidelines .................................................................................... H-2

H-2. Dimensions and Part Numbers for Swagelok

Inserts .................... H-3

H-3. Dimensions and Part Numbers for Swagelok

Ferrules .................. H-3

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 119 120

Comentarios a estos manuales

Sin comentarios

Campbell-scientific AP200 CO2/H2O Atmospheric Profile System Manual de usuario Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos de medición Campbell-scientific AP200 CO2/H2O Atmospheric Profile System