Campbell-scientific LoggerNet Datalogger Support Software Manual de usuario Pagina 479
- Pagina / 580
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 14. Troubleshooting Guide
14.8 Troubleshooting PakBus Communications
For additional information on PakBus communication, refer to our PakBus
Networking Guide (under separate cover).
Problem: LoggerNet can’t communicate with in-range PakBus datalogger
(PC-RF400~~~RF400-CR510PB~~~ RF400-CR510PB~~~CR205)
Possible reason 1: LoggerNet’s PakBus Address for datalogger
doesn’t match datalogger’s PakBus Address.
Remedy 1: Make them match.
Possible reason 2: An RF400 Series radio is set to a different
Hopping Sequence, Network Address, Radio Address, or Standby
Mode.
Remedy 2: Set both radios exactly the same in the above parameters.
(‘base’ radio’s Active Interface is typically Auto Sense, remote radio
is typically CSDC 7)
Possible reason 3: No PakBusPort in device map between root and
datalogger.
Remedy 3: Add PakBusPort.
Possible reason 4: No PakBus OS in datalogger
Remedy 4: If you have two in-range routers using neighbor filters, in
order for them to discover one another you must list each of them as a
potential neighbor in the other’s neighbor filter.
Problem: LoggerNet can’t communicate via datalogger-router to a certain
remote datalogger.
(PC-RF400~~~RF400-CR10XPB~~~RF400-CR510~~~CR205)
Possible reason 1: A datalogger router has insufficient *D15 max
nodes, max neighbors, or max routers configured.
Remedy 1: Increase the *D15 numbers.
*D15 settings of 000x, 6, 6, 6, 0 are reasonable for a router in a
network of under a half dozen nodes
*D15 settings allocate memory similar to *A. It is a good idea, when
configuring *D15 settings, to leave ‘room to grow.’ Changing *D15
settings later on could result in loss of data as *0 is entered to compile
new settings.
Possible reason 2: Last datalogger router has no means configured of
discovering the remote datalogger.
Remedy 2: Configure the datalogger router with either a neighbor
filter or a beacon. Make sure Neighbor Filter potential neighbors
14-17
- INSTRUCTION MANUAL 1
- License for Use 3
- Limited Warranty 4
- Table of Contents 5
- Product History 19
- LoggerNet Products 22
- Setup Screen 23
- Connect Screen 24
- Status Monitor 24
- Task Master 24
- Short Cut 25
- CRBasic Editor 25
- View Pro 27
- 1.1 Hardware and Software 31
- Backup Procedures 33
- 2.2 Upgrade Notes 34
- 2.3.1.1 Program Directory 35
- 2.3.1.2 Working Directories 35
- 2.3.4 Program Crashes 40
- 2.4.1.1 Write Access 41
- 2.4.1.2 Network Drives 42
- Section 3. Introduction 45
- 3.2.1.1 Toolbar Views 46
- 3.2.1.2 Favorites Category 47
- 3.2.1.3 Toolbar Menus 48
- 3.2.4 Real Time Tools 51
- 3.2.11.1 LoggerNetData 54
- 3.2.11.3 Baler 55
- Networks 57
- 4.2.4 Device Settings 63
- 4.2.4.4 Datalogger 67
- 4.2.4.5 PhoneBase 79
- 4.2.4.6 PhoneRemote 80
- 4.2.4.7 RFBase 81
- 4.2.4.8 RFRemote 82
- 4.2.4.9 RFBase-TD 83
- 4.2.4.10 RF RemoteTD 87
- 4.2.4.11 RFRemote-PB 87
- 4.2.4.12 MD9 Base 88
- 4.2.4.13 MD9 Remote 90
- 4.2.4.14 RF400 91
- 4.2.4.15 RF400 Remote 92
- 4.2.4.16 Generic Modem 94
- 4.2.4.17 PakBusPort 95
- 4.2.4.18 PakBus Router 98
- 4.2.4.19 PakBusPort HD 99
- 4.2.4.20 PakBusTcpServer 100
- 4.2.4.21 SerialPortPool 102
- 4.2.4.22 TerminalPortPool 105
- 4.2.5.2 Intervals 109
- 4.2.6 Setting the Clock 112
- 4.2.8 Setup’s Tools Menu 113
- 4.2.9 Setup’s Backup Menu 116
- 4.2.11 Selecting a View 116
- 4.3 Network Planner 118
- 4.3.5 Adding Stations Links 122
- 4.3.6 Adding Activities 124
- 4.3.7 The Station Summary 127
- 4.3.8 Configuring Devices 128
- 4.3.9 Saving Your Work 134
- Section 5. Real-Time Tools 137
- 5.1.2 Data Collection 139
- 5.1.2.2 Custom Collection 140
- 5.1.3 Ports and Flags 144
- 5.1.4 Datalogger Clock 146
- 5.1.5 Program Management 147
- 5.1.6 Program Association 148
- 5.1.7 Data Displays 149
- 5.1.8 Table Monitor 164
- 5.1.10 Terminal Emulator 169
- 5.1.11 Station Status 170
- 5.1.12 Calibration Wizard 171
- 5.2.1 Development Mode 172
- 5.2.1.1 The RTMC Workspace 173
- 5.2.1.2 Display Components 174
- 5.2.1.4 Expressions 180
- FromNewest(5,Order 181
- AvgRunOverTimeWithReset 188
- MaxRunOverTimeWithReset 188
- MinRunOverTimeWithReset 188
- 5.2.2 RTMC Run-Time 189
- 6.1 Status Monitor 191
- 6.1.2.1 Selecting Columns 193
- 6.1.2.2 Display/Subnet 198
- 6.1.2.4 Reset Device 198
- 6.1.2.6 Pool Statistics 199
- 6.1.2.7 Pool Devices 200
- 6.1.2.8 State of Operations 200
- 6.2 LogTool 202
- 6.2.1 Log Types 203
- 6.2.2 Using LogTool 203
- 6.2.3 Saving Logs to File 204
- 6.3 Comm Test 205
- 6.4 PakBus Graph 206
- 6.5 Troubleshooter 208
- 6.5.1 Status Information 209
- 6.5.2 Buttons 210
- 6.5.3 TD-RF Test 210
- TD-RF QUALITY REPORT 215
- 6.5.3.3 Advanced Features 216
- Datalogger Programs 219
- 7.2 Short Cut 220
- Datalogger 235
- 7.2.3 Short Cut Settings 236
- 7.2.3.5 Sensor Support 237
- 7.2.3.6 Integration 238
- 7.2.3.7 Font 238
- 7.3 CRBasic Editor 239
- 7.3.3 Toolbar 243
- 7.3.3.1 Compile 245
- 7.3.3.4 Templates 249
- 7.3.4 CRBasic Programming 258
- If TCTemp(1) > 100 Then 260
- Call Subroutine1 260
- End If 260
- 7.3.4.5 Line Continuation 261
- 7.3.4.7 Example Program 262
- 7.3.4.8 Data Tables 262
- 7.3.4.10 Numerical Entries 265
- 7.3.4.12 Flags 267
- 7.3.4.13 Parameter Types 267
- 7.4 Edlog 269
- 7.4.1.6 Expression Compiler 270
- 7.4.2.1 Program Structure 272
- 7.4.2.2 Edlog File Types 273
- 7.4.2.5 Program Comments 275
- 7.4.2.6 Expressions 276
- 7.4.3 Library Files 283
- 7.4.5 Display Options 284
- 7.4.6 Input Locations 285
- 7.4.8 Repetitions 286
- 7.4.9 Input Location Editor 287
- 7.4.11 Final Storage Labels 289
- 7.4.13 Program Security 291
- 7.4.15 DLD File Labels 292
- 7.4.14 Final Storage Area 2 292
- 7.4.18 PakBus Settings 294
- 7.5 Transformer Utility 295
- 7.5.2 Controls 297
- 8.1 View Pro 299
- 8.1.2 The Toolbar 300
- 8.1.3 Opening a File 302
- 8.1.5 Importing a CSV File 306
- 8.1.6 Data View 309
- 8.1.7 Graphs 311
- 8.1.7.1 Line Graph 313
- 8.1.7.2 Histogram 317
- 8.1.7.3 XY Plot 320
- 8.1.7.4 Rainflow Histogram 322
- 8.1.7.5 FFT 325
- 8.1.8 Right-click-Menus 328
- 8.1.9 Printing Options 330
- 8.2 Split 331
- 8.2.2 Getting Started 332
- 8.2.3.1 Input Files 338
- become accessible. Enter 340
- Examples: 362
- 8.2.3.2 Output Files 372
- 8.2.4 Help Option 378
- 8.2.5 Editing Commands 379
- 8.3 CardConvert 384
- 8.3.2.1 File Format 386
- 8.3.2.2 File Processing 386
- 8.3.2.3 File Naming 387
- 8.3.3 Converting the File 388
- 9.1 Task Master 391
- 9.1.1 Setup Tab 392
- 9.1.1.2 Logger Event Tasks 393
- 9.1.2 Status Tab 404
- 9.1.4 Task Master Logs 406
- LoggerNet 407
- 10.1.4 Terminal Tab 411
- 10.1.6 Off-line Mode 412
- 10.2 CoraScript 413
- 10.2.2.4 Hole Management 415
- 10.3 RWIS Administrator 416
- 10.3.3.2 Schedule Settings 419
- 10.3.3.3 Snapshots Settings 421
- 10.3.3.4 Clock Settings 422
- 10.3.4 Deleting a Station 424
- 10.4 File Format Convert 425
- 10.4.2 Options 426
- 10.5 Toa_to_tob1 428
- 11.1 Security Manager 429
- Adding an Account 430
- 11.2 Hole Monitor 433
- 11.2.2 Message Log 435
- 11.3 Data Filer 436
- 11.3.2.2 Collection Options 437
- 11.3.3 The Collected Data 439
- 11.4 Data Export 440
- 11.4.2 Theory of Operation 442
- Available for LoggerNet 451
- 12.3 RTMC Run-Time 452
- 12.4 RTMC Pro 452
- 12.5 LNDB 452
- 12.6 Baler 452
- 12.7 CSIOPC Server (PC-OPC) 453
- Communications Links 455
- 13.1.2.3 RF Address 456
- 13.1.2.4 Max Time Online 456
- 13.2 Phone to MD9 457
- 13.2.2.2 MD9 Addresses 458
- 13.2.2.4 Max Time Online 458
- 13.3 TCP/IP to RF 459
- Third-Party 460
- Serial Server 460
- Campbell Scientific 460
- RF Network Base 460
- 14.1 What’s Changed? 463
- 14.2.2 Socket Errors 464
- Attenuation Pads 474
- (10 - 20 dB) 474
- Programmable 474
- Formats 495
- B.1.2 ASCII Printable 496
- B.1.3 TOACI1 496
- B.1.3.1 Field Name Suffixes 497
- B.1.4 TOA5 498
- B.1.5 TOB1 498
- B.1.6 Array Compatible CSV 500
- B.1.7 CSIXML 500
- B.1.7.2 File Syntax 502
- B.1.7.3 The csixml Element 504
- B.1.7.4 File Example 506
- B.1.8 CSIJSON 508
- B.1.8.2 File Syntax 509
- B.1.8.3 File Example 512
- B.2 Datalogger Data Formats 513
- B.3 Binary Data Value Types 515
- B.4.1 Split 516
- B.4.2 View Pro 516
- B.4.3 CardConvert 516
- B.4.4 File Format Convert 516
- B.5 RTMS Format Description 517
- CR200, and CR9000 519
- Programs and Data Storage 520
- C.3 Table Data Overview 523
- C.4 Default Tables 524
- D.2.1 Organization 529
- D.2.2 Operation 529
- D.3 Directory Organization 531
- (Program File Directory) 532
- Appendix E. Log Files 533
- E.1.2 Enabling Log Files 534
- E.2 CQR Log (RF Link) 554
- F.1 Calibration Essentials 555
- F.3.1 Zeroing 557
- F.3.2 Offset Calibration 558
- Control 559
- Calibration 560
- Programs 562
- and press Next 563
- Step 1 of 3 571
- Step 2 of 3 572
- Step 3 of 3 573
Relacionado con productos y manuales para Software Campbell-scientific LoggerNet Datalogger Support Software
Software Campbell-scientific PONDVIEW Real-Time Monitoring & Control Softwa Manual de usuario
(38 paginas)
(38 paginas)
Software Campbell-scientific RTMC Pro Real-Time Monitor and Control Professiona Manual de usuario
(76 paginas)
(76 paginas)
Software Campbell-scientific Software Development Kit Beginner's Guide Manual de usuario
(22 paginas)
(22 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales