Campbell-scientific RTDAQ Software Manual de usuario Pagina 282
- Pagina / 368
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 10. Utilities
10.2.5 The Unknown Device Type
When the Unknown Device type is selected, a panel will be shown in the tab
control similar to that shown below:
Clicking Connect puts DevConfig into Terminal emulation mode on the Serial
Port and at the Baud Rate selected.
When you click on Identify Datalogger Type, DevConfig will attempt to
identify the type of device that is connected on the specified serial port. It will
attempt to communicate using each of the datalogger protocols (mixed-array,
table-data, and PakBus) in turn. If it fails to get any answer to any of these
attempts, the baud rate will be automatically changed and the various protocols
will be attempted again. When DevConfig recognizes the response from the
device and the device type is one of the supported types, that device type will
automatically be selected.
10.2.6 Off-line Mode
Many devices in DevConfig have an off-line mode available that allows you to
browse the device’s settings without actually being connected to a device. You
can select a device, and then select Off-line Mode from DevConfig’s File
menu. You will be able to see the device’s settings and associated help. You
can also make changes to the settings and then press Apply to bring up the
option to Save or Print the configuration. Saving the configuration will allow
you to load it into a device at a later time.
10-12
- Revision: 3/12 1
- Campbell Scientific, Inc 3
- RTDAQ Table of Contents 5
- Appendices 12
- Figures 13
- Section 1. Introduction 19
- 1.1 RTDAQ Overview 20
- 1.1.3 Monitor Data 21
- 1.1.4 Collect Data 24
- 1.1.7 View Pro 26
- 1.1.8 Split 27
- 1.1.9 CardConvert 27
- 1.1.10 Short Cut 27
- 1.1.11 CRBasic Editor 28
- 1.3 Windows Conventions 29
- 2.1 Hardware and Software 31
- Backup Procedures 33
- 3.2.1.1 Program Directory 34
- 3.2.1.2 Working Directories 34
- 3.2.2.1 Performing a Backup 36
- 4.1 Overview 37
- 4.2 EZSetup Wizard 39
- 4.2.2 Communication Setup 40
- 4.2.3 Datalogger Settings 40
- 4.2.5 Send Program 41
- 4.3 Clock/Program Tab 42
- 4.4 Monitor Data Tab 43
- 4.5 Collect Data Tab 44
- 4.6 Pull-down Menus 45
- 4.6.3 Datalogger Menu 46
- 4.6.3.4 File Control 48
- 4.6.3.5 Calibration Wizard 51
- 4.6.3.6 Terminal Emulator 52
- 4.6.4 Network Menu 53
- 4.6.5 Tools Menu 54
- 4.6.5.2 Options 55
- 4.6.5.3 LogTool 55
- 4.6.5.4 PakBus Graph 57
- 4.7 The RTDAQ Toolbar 59
- Editing 61
- 5.1.3 Toolbar 65
- 5.1.3.1 Compile 67
- 5.1.3.4 Templates 71
- 5.1.4 CRBasic Programming 80
- 5.1.4.5 Line Continuation 82
- 5.1.4.7 Example Program 84
- 5.1.4.8 Data Tables 84
- 5.1.4.10 Numerical Entries 87
- 5.1.4.12 Flags 89
- 5.1.4.13 Parameter Types 89
- 5.2 Short Cut 91
- Datalogger 106
- 5.2.3 Short Cut Settings 107
- 5.2.3.5 Sensor Support 108
- 5.2.3.6 Integration 109
- 5.2.3.7 Font 109
- Generator 110
- 5.3.2 Program Startup 111
- 5.3.4.2 File 113
- 5.3.4.1 File 113
- 5.3.4.3 File 114
- 5.3.4.7 File 115
- 5.3.5 Using Save and Send 116
- 5.3.5.1 Download 117
- 5.3.5.2 Run Options 118
- 5.3.5.3 Datalogger Response 118
- Section 6. View Pro 119
- 6.2 The Toolbar 120
- 6.3 Opening a File 122
- 6.4.1 Selecting a Database 123
- SQL Server 124
- 6.4.2 Selecting a Table 126
- 6.5 Importing a CSV File 127
- 6.6 Data View 129
- 6.7 Graphs 131
- 6.7.1 Line Graph 132
- 6.7.1.2 Graph Width 133
- 6.7.1.3 Scrolling 134
- 6.7.1.4 Graph Cursor 134
- 6.7.1.5 Line Graph Toolbar 135
- 6.7.2 Histogram 136
- 6.7.2.2 Options 139
- 6.7.2.3 Histogram Toolbar 139
- 6.7.3 XY Plot 140
- 6.7.3.3 XY Plot Toolbar 141
- 6.7.4 Rainflow Histogram 142
- 6.7.4.2 Options 144
- 6.7.5 FFT 146
- 6.7.5.2 Options 148
- 6.7.5.3 FFT Toolbar 148
- 6.8 Right-click-Menus 149
- 6.9 Printing Options 151
- 6.10 View Pro Online Help 152
- 7.1.5.1 Display Tab 157
- 7.1.5.2 Alarms Tab 158
- 7.1.5.3 Setup Tab 159
- 7.2 Ports and Flags 160
- 7.3 Table Monitor 161
- 7.3.2.1 Start and Stop 163
- 7.3.2.2 Reset Table 164
- 7.3.2.3 Fields and Values 164
- 7.4 Real Time Graph 166
- 7.4.2 Adding Ite 168
- 7.4.4 Basic Graph Operation 168
- 7.4.5 Zooming a 170
- 7.4.9 Setting th 174
- 7.4.9.3 Visual Disp 177
- 7.4.9.5 Using Save 180
- 7.5 Fast Graph 181
- 7.6 XY Plot 182
- 7.6.2 Setting up 184
- the XY Plot for Display 184
- Points per Field 186
- 7.6.2.2 Number of 186
- 7.6.2.3 Right-Click 187
- Functionality 187
- 7.6.5 Zooming w 193
- 7.6.6.1 Scaling Tab 195
- 7.6.6.2 Data Display Tab 196
- 7.6.6.3 Visual Display Tab 197
- 7.6.6.4 Trace Tab 197
- 7.6.6.5 Save Tab 199
- 7.7 Histogram Monitoring 200
- 7.7.2 Displaying 201
- Histograms 201
- 7.8.2 FFT vs. FFTSample 203
- 7.9.1 Moving an 205
- 7.9.3 Using the Buttons 206
- 7.9.4 3D View 207
- 7.9.5 X-Axis Mode 209
- 7.9.8.1 Scaling the Axes 212
- Options 217
- 7.10 Rainflow Hi 218
- 7.10.6 X-Axis Mode 224
- 7.10.9 Setting th 227
- 7.10.9.3 Trace Options 229
- 7.11 Saving and 232
- Loading Configurations 232
- 7.11.2 Using Co 233
- Control Software 235
- 8.1.1 The RTMC Workspace 237
- 8.1.3 Display Components 237
- 8.1.4.1 File Menu 239
- 8.1.4.2 Edit Menu 240
- 8.1.4.3 View Menu 240
- 8.1.4.4 Project Menu 241
- 8.1.4.5 Screen Menu 241
- 8.1.4.6 Component Menu 242
- 8.1.5 Expressions 243
- 8.1.5.1 Operators 246
- 8.1.5.2 Order of Precedence 246
- 8.1.5.5 Functions 247
- Description 248
- 8.1.5.9 Time Functions 250
- AvgRunOverTimeWithReset 251
- MaxRunOverTimeWithReset 251
- 8.2 RTMC Run-time 252
- 9.1 Calibration Essentials 255
- 9.3.1 Zeroing 257
- 9.3.2 Offset Calibration 258
- Control 260
- Calibration 261
- Programs 263
- Section 10. Utilities 271
- 10.1.2.1 File Format 272
- 10.1.2.2 File Processing 273
- 10.1.2.3 File Naming 274
- 10.1.2.4 TOA5/TOB1 Format 274
- 10.1.3 Converting the File 275
- 10.2.1 Overview 277
- 10.2.4 Terminal Tab 281
- 10.2.6 Off-line Mode 282
- 10.3 Split 283
- 10.3.2 Getting Started 284
- 10.3.3.1 Input Files 290
- Examples: 314
- Monthly Summary Example 317
- Table-based dataloggers 322
- 10.3.3.2 Output Files 324
- 10.3.4 Help Option 330
- 10.3.5 Editing Commands 331
- 10.3.7 Log Files 336
- 10.4.1 Event Logging 337
- 10.4.2 CQR Log (RF Link) 354
- Formats 357
- A.1.2 TOB1 358
- A.2 Datalogger Data Formats 359
- A.3 Binary Data Value Types 361
- A.3.4 IEEE8 362
- A.4.1 Split 362
- A.4.2 CardConvert 362
- Step 1 of 3 363
- Step 2 of 3 364
- Step 3 of 3 365
Relacionado con productos y manuales para Software Campbell-scientific RTDAQ Software
(22 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales