Campbell-scientific LP02 Hukseflux Pyranometer Manual de usuario Pagina 1

INSTRUCTION MANUAL LP02 Pyranometer Revision: 1/14 Copyright © 2006- 2014 Campbell Scientific, Inc.

LP02 Pyranometer FIGURE 4-4. CM225 Bracket Mounting Holes 3. Place the mounting screws in the mounting holes and slightly tighten them. The leveli

LP02 Pyranometer 5. Tighten the mounting screws to secure the assembly in its final position. 6. Route the sensor cable to the instrument enclosure

LP02 Pyranometer 3. Select LP02 Pyranometer, and select the right arrow (in center of screen) to add it to the list of sensors to be measured, and th

LP02 Pyranometer 5. Choose the Outputs and then select Finish. 6. In the Save As window, enter an appropriate file name and select Save. 7. In t

LP02 Pyranometer 5. Overview The LP02 pyranometer is designed for continuous outdoor use. Due to its flat spectral sensitivity from 280 to 3000 nm,

LP02 Pyranometer Compatible Dataloggers: CR800 CR850 CR1000 CR3000 CR9000(X) CR5000 CR23X CR10(X) CR510 CR500

LP02 Pyranometer 7. Operation 7.1 Wiring A schematic diagram of the LP02 is shown in FIGURE 7-1. White Green Clear FIGURE 7-1. LP02 Schematic

LP02 Pyranometer TABLE 7-2. Single-Ended Connections to Campbell Scientific Dataloggers Color Description CR9000(X) CR5000 CR3000 CR1000 C

LP02 Pyranometer individual sensor and the maximum expected reading. With some dataloggers, an autorange option can be used if measurement time is no

LP02 Pyranometer Wiring for the examples is given in TABLE 7-4. TABLE 7-4. Wiring for Example Programs Color Description CR1000 CR10X White Signa

LP02 Pyranometer 'Call Data Tables and Store Data CallTable(Table1) CallTable(Table2) NextScan EndProg 7.2.4.2 CR10X Example Prog

LP02 Pyranometer 9: Average (P71) 1: 1 Reps 2: 3 Loc [ Solar_Wm2 ] 10: If time is (P92) 1: 0 Minutes (Seconds --) into a 2: 14

LP02 Pyranometer 8. Maintenance Inspect and clean the outer dome at regular intervals, for example, every week or so. Clean any accumulated dust, et

LP02 Pyranometer Symptom: sensor signal shows unexpected variations 1. Check for the presence of strong sources of electromagnetic radiation (radar,

LP02 Pyranometer 18

Appendix A. CM245 Adjustable Angle Mounting Stand A.1 Installation The CM245 includes slots that allow it to be adjusted to any angle from horizont

Appendix A. CM245 Adjustable Angle Mounting Stand FIGURE A-2. CM245 bracket with 1.5 in. U-bolts positioned to mount pyranometer at a 40

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbel

Warranty “PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are warranted by Campbell Scientific, Inc. (“Campbell”) to be free from defects in materi

Assistance Products may not be returned without prior authorization. The following contact information is for US and international customers residing

Table of Contents PDF viewers: These page numbers refer to the printed version of this document. Use the PDF reader bookmarks tab for links to spec

Table of Contents 4-4. CM225 Bracket Mounting Holes ... 4 4-5. LP02 Pyranometer Attached to CM2

LP02 Pyranometer 1. Introduction The LP02 is an ISO-second-class pyranometer that monitors solar radiation for the full solar spectrum range. It pr

LP02 Pyranometer 4. Quickstart Please review Section 7, Operation, for wiring, CRBasic programming, and Edlog programming. 4.1 Siting Consideration

LP02 Pyranometer FIGURE 4-2. CM225 Bracket Attached to a Mast 2. Place the LP02 in the center of the CM225 with the cable pointing to the nearest m