Campbell-scientific AVW1 and AVW4 Interfaces for Vibrating Wire Sensor Manual de usuario descargar pdf (Pagina 23)

AVW1/AVW4

5-3

02: P55 Polynomial

01: 4 Reps

02: 1 X Loc TEMP C #1

03: 1 F(X) Loc [:TEMP C #1]

04: -104.78 C0

05: 378.11 C1

06: -611.59 C2

07: 544.27 C3

08: -240.91 C4

09: 43.089 C5

03: P28 Vibrating Wire (SE)

01: 4 Reps

02: 5 IN Chan

03: 1 Excite all reps w/EXchan 1

04: 24 Starting Freq. (units=100 Hz)

05: 31 End Freq. (units=100 Hz)

06: 500 No. of Cycles

07: 500 Rep delay (units=.01sec) 5

SEC DELAY BETWEEN

MEASUREMENTS

08: 5 Loc [:P psi #1]

09: 1 Mult

10: 0 Offset

04: P53 Scaling Array (A*loc +B)

APPLY MULT & OFFSET

01: 5 Start Loc [:P psi #1]

02: -15.1 A1

03: 142.4 B1

04: -15.1 A2

05: 142.4 B2

06: -15.1 A3

07: 142.4 B3

08: -15.1 A4

09: 142.4 B4

05: P53 Scaling Array (A*loc +B)

LOADS TEMP. COEFF.

01: 13 Start Loc [:Cpsi/C #1]

02: 0 A1

03: -.0698 B1

04: 0 A2

05: -.0698 B2

06: 0 A3

07: -.0698 B3

08: 0 A4

09: -.0698 B4

06: P87 Beginning of Loop

TEMPERATURE

CORRECTION

01: 00 Delay

02: 4 Loop Count

07: P34 Z=X+F ASSUMES

CALIBRATION TEMP. = 24

o

C

01: 1-- X Loc TEMP C #1

02: -24 F

03: 17-- Z Loc [:T-To*C #1]

08: P36 Z=X*Y

01: 13-- X Loc Cpsi/C #1

02: 17-- Y Loc T-To*C #1

03: 17-- Z Loc [:T-To*C #1]

09: P33 Z=X+Y

01: 5-- X Loc psi #1

02: 17-- Y Loc T-To*C #1

03: 9-- Z Loc [:Pt psi #1]

10: P95 End

FOLLOWING THREE INSTRUCTIONS

SUBTRACT THE BAROMETRIC PRESSURE

FROM THE THREE WATER PRESSURES

11: P35 Z=X-Y

01: 10 X Loc Ptb psi #2

02: 9 Y Loc Pt psi #1

03: 10 Z Loc [:Ptb psi #2]

12: P35 Z=X-Y

01: 11 X Loc Ptb psi #3

02: 9 Y Loc Pt psi #1

03: 11 Z Loc [:Ptb psi #3]

13: P35 Z=X-Y

01: 12 X Loc Ptb psi #4

02: 9 Y Loc Pt psi #1

03: 12 Z Loc [:Ptb psi #4]

First 99 Input Location Labels:

1:TEMP C #1 11:Ptbpsi #3

2:TEMP C #2 12:Ptbpsi #4

3:TEMP C #3 13:Cpsi/C #1

4:TEMP C #4 14:Cpsi/C #2

5:P psi #1 15:Cpsi/C #3

6:P psi #2 16:Cpsi/C #4

7:P psi #3 17:T-To*C #1

8:P psi #4 18:T-To*C #2

9:Pt psi #1 19:T-To*C #3

10:Ptbpsi #2 20:T-To*C #42

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 35 36

Comentarios a estos manuales

Sin comentarios